国产在线精品二区,强行挺进少妇紧窄湿润,无码国内精品人妻少妇,午夜色大片在线观看

HomeHotlineContact
0position:Home>>News

Analysis of the reasons for the creeping and vibration of the edge milling machine

source:   author: time:2020-08-15 Visits:1884
There are many obvious abnormal phenomena in the milling machine, but in some economic CNC systems, there is no alarm. Even if there is an alarm sometimes, the alarm information shows that it is not the alarm of abnormal phenomenon you see. The creeping and vibration of the milling machine is an obvious example. When the milling machine runs at a low speed, the worktable of the CNC milling machine moves forward in a creeping manner; when the milling machine runs at a high speed, there will be vibration.

Because of the bad lubrication, the friction resistance increases when the milling machine table moves. When the motor is driven, the table does not move forward, which makes the ball screw produce elastic deformation and stores the energy of the motor on the deformation. When the motor continues to drive and the elastic force produced by the stored energy is greater than the static friction force, the milling machine table creeps forward and moves in this way again and again, resulting in crawling phenomenon.

Because the vibration frequency is proportional to the speed of the motor, the first thing to do is to check whether there is a fault in the motor, check the surface condition of the carbon brush and commutator, as well as the mechanical vibration, and check the lubrication of the ball bearing. The whole inspection does not need to be disassembled completely, but can be observed by the inspector. The bearing can listen to the sound with ears To check. If there is no problem, check the tachogenerator. The tachogenerator is usually DC.

A closed loop system may also cause system oscillation due to poor parameter setting. However, the best way to eliminate this oscillation is to reduce its magnification, to adjust RV1 and reverse clock direction in the FANUC system. At this time it can be seen that it will become better immediately. However, because of the relatively small range of RV1 regulating potentiometers, sometimes it can not be adjusted, it can only change the short circuited bar. Cut off the feedback resistance and reduce the magnification of the whole regulator.

More edge milling machines, with pressure beam milling machine, no pressure beam edge milling machine, end face milling machine, end face milling machine, planer. Please pay attention www.weituocnc.com


All rights reserved:WUXISHI XILI MILLING MACHINE CO.,LTD(www.weituocnc.com)  Su ICP 15043207-1 Design :25318.cn

欧美三级午夜理伦三级| 无码人妻一区二区三区av| 成人午夜高潮a∨猛片 | 日日碰狠狠添天天爽无码| 亚洲综合国产成人丁香五月激情| 国产无遮挡又黄又爽不要vip网站 精品一区二区三区波多野结衣 | aa级女人大片免费视频| 岳好紧好湿夹太紧了好爽矜持| 人妻暴雨中被强制侵犯在线| 国产网红女主播精品视频| 亚洲精品97久久中文字幕无码| 国产福利在线永久视频| 双乳被一左一右吃着动态图| 国模肉肉超大尺度啪啪| 影音先锋人妻啪啪av资源网站 | 精品久久久久久久久中文字幕| 韩国三级丰满少妇高潮| 好吊色欧美一区二区三区视频 | 国产真实伦在线观看| 久久99精品国产麻豆婷婷| 最新国自产拍av| 久久天天躁狠狠躁夜夜avapp | 狠狠躁夜夜躁人人躁婷婷视频| 免费a级毛片在线播放不收费| 中文字幕在线播放| 久久久久无码精品国产| av激情亚洲男人的天堂国语| 无码少妇一区二区浪潮av| 久久99精品国产99久久6尤物| 男男h黄漫画啪啪无遮挡| 国产亚洲人成在线播放| 午夜丰满少妇性开放视频| 久久精品国产精品亚洲毛片| 88国产精品视频一区二区三区| 精品熟女少妇av免费久久| 亚洲国产av一区二区三区| 国产白丝无码免费视频| 亚洲国产成人久久一区二区三区| 欧洲美熟女乱又伦av影片| 国产亚洲精品美女久久久久| 成年女人wwxx免费国产|